READ THIS FIRST!

When you restore or reset your keyboard to it's factory settings you will lose all your work you have saved on the keyboard. The keyboard should reset itself, like it just came off the factory line. Drums Unlimited Rentals nor any of their employees are responsible for any damages. Factory resets should only be done as a last resort! If you do not feel comfortable doing this yourself, then you should have it done by a certified repair technician.

The Backline Tech's Guide to Keyboard Factory Presets!

...because the "Panic" Button only stops the Midi from freaking out, not you.


Alesis

QS 8.1 64 Voice Expandable Synthesizer

Reset Factory Defaults:

  1. Turn the “VOLUME” and “MODULATION” WHEELS all the way DOWN.
  2. Power OFF the keyboard
  3. Hold down the bottons “0" and “3" and turn back ON.
  4. You will know it did it’s thing, if there isn’t any name, in the top row of the display.


Ensoniq

ASR 10

Reset Factory Defaults:
  1. None. Insert the Operating Software disk and turn it on
  2. It will set it’s self up. OR...
Load Operating system and sounds from Disk
  1. Insert Disk
  2. “COMMAND”
  3. “SYSTEM/MIDI”
  4. “3"
  5. Select “LOAD GLOBAL PARAMETERS”
  6. “ENTER/YES”
  7. and so on and so on...

EPS 16 Plus Digital Sampling Workstation

Reset Factory Defaults:
  1. None. Must load Operating system and sounds from Disk each time you power on
  2. Insert Disk
  3. “COMMAND”
  4. “SYSTEM/MIDI”
  5. ARROW RIGHT to select “LOAD GLOBAL PARAMETERS”
  6. “ENTER/YES”

SD-1 Music Production Synthesizer

Reset Factory Defaults:
  1. Hold down the “PRESETS” button while pressing the “soft” button on the TOP LEFT corner of the LCD Display
  2. Message Appears “ ERASE MEMORY...”
  3. “YES”
  4. Almost Done...
Now you will need to reinstall the “Sequencer Operating System” from the Master SD-1 Disk
  1. At the top of the center bank of buttons under “System” press the “Storage” button
  2. “DISK”
  3. “LOAD”
  4. ARROW all the way up to “Sequencer_OS”
  5. Press “SOUNDS” at the bottom left of the display
  6. “YES” button.
Sustain Pedal:
  1. Under the “System” area press the “Master” button repeatedly and it wil page you through the settings
  2. Look for “Footswitch” on the bottom and select that “FS2" = “Sustain”
  3. Press “Sounds” to escape.

TS 10 / TS 12 Performance / Composition Synthesizer

Reset Factory Defaults:
  1. Hold down the “PRESETS” button while pressing the “soft” button on the TOP LEFT corner of the LCD Display
  2. Message Appears “ ERASE MEMORY...”
  3. “YES”
  4. Let it do it’s thing.
Sustain Pedal:
  1. Press “System” button in Top Row of the center Bank repeatedly until you see “System Foot-SW1
  2. It should read “L = unused R=sustain”

Hammond

XB-2

Reset Factory Defaults:
  1. “EDIT” button
  2. Press “8" twice
  3. Press “2"

XK-3

Reset Factory Defaults:
  1. Switch off the unit then power back on while holding “REC/JUMP”
  2. Hold till ”Loading Default...” appears.
Sustain Pedal:
  1. “MENU” button
  2. “4" button
  3. Page UP ARROW 4 times
  4. Left/Right knob to select “Pedal” or “CU-1"
  5. “PLAY” button to exit.

Korg

CX-3 Combo Organ

Reset Factory Defaults:
  1. Press “GLOBAL” Button
  2. Press “PROGRAM” (7) button
  3. Press RIGHT ARROW key “>” It should display “ Copy Swap Init” If not find it.
  4. Press “WRITE/ENTER” button and “Copy” will blink
  5. Press the “+” button 5 times “Init All Data” will display on the left and “All Data” will blink
  6. Press “WRITE/ENTER”
  7. Press “WRITE/ENTER” again to confirm
  8. Once it’s finished press “EXIT” twice to return.
Sustain Pedal:
  1. Press “GLOBAL” button
  2. Press “PROGRAM” (1) button
  3. Press RIGHT ARROW key “>” a total of...
  1. - 10 times or just find “Pedal 1 SW Polarity” –> Use “Bank” “-“ or “+” to change.
  2. - 11 times or just find “Pedal 2 SW Polarity” –> Use “Bank” “-“ or “+” to change.

Karma Music Workstation

Reset Factory Defaults:
  1. Factory disk needed
  2. Insert disk labeled “KMFD-00P into drive
  3. Press “DISK” button
  4. “F1" (Load) button
  5. Use cursor arrows Up/Down to select “PRELOAD.PCG”
  6. “F8" (UTILITY)
  7. Arrow down to choose “Load Selected”
  8. “F8" (OK)
  9. “F8" (OK) again to execute
  10. Wait until it finishes.

M1 Music Workstation

Turn Off Write Protect:
  1. “GLOBAL” button
  2. “6" button on numeric keypad
  3. Choose “B” = Internal or “E” = Card
  4. Up and Down ARROWS to change. (ON/OFF)
Reset Factory Defaults:
  1. Load the reset Data from the BLACK Preload RAM Card. Press “GLOBAL” button
  2. Press “8" on the numeric keypad
  3. Use “Value” Slider “B” or select “PROG/COMBI/SEQ”
  4. “G” to (LOAD)
  5. Press “G” (YES) again to confirm
  6. “COMBI” to exit.
Sustain Pedal:
  1. “GLOBAL” button
  2. “2" button on numeric keypad
  3. Up and Down ARROWS to change value.

M1 Ex Music Workstation

Turn Off Write Protect:
  1. “GLOBAL” button
  2. “6" button on numeric keypad
  3. Choose “B” = Internal or “E” = Card
  4. Up and Down ARROWS to change. (ON/OFF)
Reset Factory Defaults:
  1. Load the reset data from the WHITE Preload RAM Card.
  2. Press “GLOBAL” button
  3. Press “8" on the numeric keypad
  4. Use “Value” Slider “B” or select “PROG/COMBI/SEQ”
  5. “G” to (LOAD)
  6. Press “G” (YES) again to confirm
  7. “COMBI” to exit.
Sustain Pedal:
  1. “GLOBAL” button
  2. “2" button on numeric keypad
  3. Up and Down ARROWS to change value.

MS2000 Analog Modeling Synthesizer

Turn Off Write Protect:
  1. “GLOBAL” buttonr in the upper right
  2. “SELECT” (4) button in the bottom row
  3. Press “-/NO” button under the display.
Reset Factory Defaults:
  1. “GLOBAL” button
  2. “SELECT” (4) button
  3. Press the RIGHT ARROW cursor arrow 3 times
  4. It says “Preload?” select the “+/YES” button
  5. Use the “-/NO” and “+/YES” to select “GLOBAL”
  6. Use RIGHT ARROW cursor to select “OK”
  7. Press the ”+/YES” button
  8. “+/YES” again to confirm
  9. Press “Exit” button to exit.

N264 - N364 Music Workstations

Turn Off Write Protect:
  1. “GLOBAL” button
  2. UP ARROW to select up to different protects (4A, 4B, 4C and 4D Protects)
  3. UP/DOWN “VALUE” ARROWS to change.
Reset Factory Defaults:
  1. Insert “N264/N364 Preload Program”
  2. “Directory ok?” appears press “YES”
  3. Use the Value Slider to select the “PREOAD” file to load
  4. ARROW cursor over to “OK”
  5. “YES"
  6. “YES” again to confirm
  7. Wait until completed.
Sustain Pedal:
  1. “GLOBAL” button
  2. UP ARROW to select “7B”
  3. “VALUE” ARROWS up/down to change.

O1/W - O1/WFD - O1/W pro - O1/W proX Music Workstations

Turn Off Write Protect:
  1. “GLOBAL” button
  2. “PAGE” “-“ or “+” to select “P4"
  3. Up/Down cursor position to “Protect” (A=Prog E=Combi G=Seq)
  4. “VALUE” slider to change.
Reset Factory Defaults:
  1. “GLOBAL” button
  2. “Page +” or “Page -“ to select “P7" (Preload)
  3. Select “Load Cobi/Prog”
  4. Button “A” to select “Bank-A+B”
  5. Button “D” to Select “Bank-A+B”
  6. Press “G” (LOAD)
  7. “E” (YES) to confirm.
Sustain Pedal:
  1. “GLOBAL” button
  2. “Page” “-“ or “+” to select “P4"
  3. Up/Down cursor position to “Damper Switch Polarity”
  4. “VALUE” slider to change.

Prophecy Solo Synthesizer

Turn Off Write Protect:
  1. On the upper right, you have to Press the Row Select button first. It’s in the top row 2nd button with the arrows above it.
  2. Select “GLOBAL” button that’s to the right of that.
  3. Select “GLB-20" (Memory Protect) with the PAGE RIGHT buttons that are left of the display
  4. Set to them to “OFF” buy using the “CURSOR” ARROWS left or right to select
  5. “VALUE” + or - to change (OFF/ON)
Reset Factory Defaults:
  1. On the upper right, you have to Press the Row Select button first. It’s in the top row 2nd button with the arrows above it.
  2. Select “GLOBAL” button that’s to the right of that.
  3. Select “GLB-19" (Load FactoryData) with the “PAGE” right and left buttons that are left of the display
  4. CURSOR LEFT so it selects the bottom left value on the display
  5. “VALUE +” button to select “All_Data”
  6. Press “ENTER” button
  7. “ENTER” again.
Calibrate Controllers Procedure:
  1. “GLOBAL”
  2. Select “GLB-22" (Controller Calibration)
  3. Go over all the procedures for each of the Wheels and Ribbons
  1. Wheel 1 and 3 - All the way forward and back and the middle “Dead” area.
  2. Wheel 2 - All the way forward and back only.
  3. Ribbon_X - All the way left and right.
  4. Ribbon_Z - Adjusts range when pressed.

SG Pro X

Turn Off Write Protect:
  1. “GLOBAL” button
  2. “12" button for “Prog Protect” -and- “13" button for “Perf Protect”
  3. “Value” “Yes” or “No” to change setting from on to OFF.
Reset Factory Defaults:
  1. “GLOBAL” button
  2. “14" button
  3. Cursor ARROW under display RIGHT 2 times
  4. “VALUE” slider all the way up to select “ALL”
  5. Cursor ARROW RIGHT to “OK” with “ALL” on the display
  6. “YES”
  7. “YES” to confirm
  8. “Performance” button to exit.
Sustain Pedal:
  1. “GLOBAL” button
  2. “5" button
  3. “VALUE” “YES” or “NO” to change settings.

T1 - T2 - T3 WorkStation (All the same procedure)

  • Turn Off Write Protect:
    1. “GLOBAL” button
    2. “PAGE +” or “PAGE -“ to find “GLOBAL PROTECT”
    3. “Cursor” up or down to select
    4. “Value” up or down to change settings.
    Reset Factory Defaults:
    1. You need the factory disk to reset. Use the Green disk labled “T-3"
    2. Press Mode Select key “DISK”
    3. Press “BANK/PAGE” key “0"
    4. Move the cursor to “All Data”
    5. Use the “VALUE” slider and up and down arrows to select
    6. Press “G” (Load)
    7. Confirm with the “E” (YES) key
    8. Press “COMBI” to return.
    Sustain Pedal: “GLOBAL” button
    1. Cursor down to “Damper Switch Polarity”
    2. “VALUE” slider up or down to change setting.

    TRINITY Music Workstation DRS

    Turn Off Write Protect:
    1. “GLOBAL” button
    2. “P2"
    3. Finger select in the bottom “Protect” area.
    Reset Factory Defaults:
    1. Insert Disk “TFD-00P”
    2. “DISK” button
    3. Press Load tab
    4. Select “PRELOAD1.PCG” for basic Trinity or “V3_PLOAD.PCG for V3 version
    5. Press the Page Menu button in the top right corner (Down Arrow)
    6. Press “Load Selected”
    7. “OK”
    8. Wait until after it says, “Writing to Internal Memory.” Thanks.
    Sustain Pedal:
    1. “GLOBAL” button
    2. “P1" button
    3. Finger select “Sustain Pedal”
    4. Use “VALUE” to change setting.

    TRITON / TRITON pro / TRITON proX

    Turn Off Write Protect:
    1. “GLOBAL” button
    2. “System Prefs” tab at the bottom of the display
    3. Finger select in “Memory Protect” area
    4. “COMBI” to exit.
    Reset Factory Defaults:
    1. Insert disk “TNFD-00P”
    2. ”DISK” button
    3. Press the Load Tab
    4. Press “PRELOAD.PCG”
    5. Press the Page Menu button in the top right corner (Down Arrow) and select “Load Selected”
    6. Press “OK”
    7. Wait until after it displays, “Writing To Internal Memory.”
    Sustain Pedal:
    1. “GLOBAL” button
    2. “Menu” button
    3. Choose screen “P2:Controller”
    4. Soft screen touch to select and change values
    5. “COMBI” to exit.

    TRITON Extreme Music Workstation/Sampler

    Turn Off Write Protect:
    1. “GLOBAL” button
    2. “System Prefs” tab at the bottom of the display
    3. Finger select in “Memory Protect” area
    4. “COMBI” to exit.
    Reset Factory Defaults Quickly:
    1. Turn off the unit then turn back on while holding down both the “MENU” and “EXIT” buttons. Loads All “preload” and demo data.
    Reset Factory Defaults Normally:
    1. “GLOBAL” (If you don’t see the Global basic setup page hit “EXIT” and press the “Basic” tab)
    2. Press the Page Menu button in the top right corner (Down Arrow) and choose “Load Preload/Demo Data”
    3. Select “All Preload PCG”
    4. “OK”
    5. “OK” again.
    Sustain Pedal:
    1. “GLOBAL” button
    2. “Menu” button
    3. Choose screen “P2:Controller”
    4. Soft screen touch to select and change values
    5. “COMBI” to exit.

    TRITON-Rack Expandable HI Module/Sampler

    Reset Factory Defaults:
    1. Insert the floppy disk called “TNRFD-00P”
    2. ”DISK”
    3. “F1” (LOAD)
    4. Using the ARROWS select “PRELOAD.PCG”
    5. “F8" ( UTILITY)
    6. Select Utility “Load Selected”
    7. “F8" (OK)
    8. Set “.PCG contents” to “All”
    9. Press “F8" (OK)
    10. “COMBI” to exit.

    TRITON Studio

    Turn Off Write Protect:
    1. “GLOBAL” button
    2. “System Prefs” tab at the bottom of the display
    3. Finger select in “Memory Protect” area
    4. “COMBI” to exit.
    Reset Factory Defaults:
    1. Insert Disk labled “TNSFD-00P”
    2. Enter Disk Mode and touch the LCD screen so it detects the disk
    3. Load tab
    4. Use “Drive Select” to located the proper FD drive
    5. Select “PRELOAD.PCG”
    6. Press “LOAD” tab drop down menu in the top right of the display
    7. “Load Selected”
    8. Select “.PCG Contents” to “All”
    9. “OK”
    10. “COMBI” button to exit.
    Sustain Pedal:
    1. “GLOBAL” button
    2. “Menu” button
    3. Choose screen “P2:Controller”
    4. Soft screen touch to select and change values
    5. “COMBI” to exit.

    Wavestation Advanced Vector Synthesis

    Reset Factory Defaults:
    1. Insert Card
    2. “GLOBAL”
    3. “UTIL”
    4. “MOVE”
    5. Set to “ALL”

    X-2 / X-3 Music Workstation

    Turn Off Write Protect:
    1. “GLOBAL” button
    2. Cursor ARROW UP to “4A,4B, 4C” Protects
    3. “VALUE” up/down to change settings “ON” or “OFF”.
    Reset Factory Defaults:
    1. Needs Factory Disk. Insert Floppy disk
    2. “DISK” button
    3. Hold cursor ARROW DOWN until “LOAD ALL”
    4. Message “Directory OK?” appears
    5. Press “YES”
    6. Use value Slider to select the .PCG file
    7. (X-2 = X2P_LOAD.PCG) (X-3 = X3P_LOAD.PCG)
    8. Position the cursor ARROW RIGHT to “OK”
    9. Press “YES”
    10. Press “YES” Again to confirm
    11. “COMBI” to exit.
    Sustain Pedal:
    1. “GLOBAL” button
    2. Cursor ARROW UP to “8C:Damper Polarity”. (HINT: You can just hold the arow up until it stops. It’s the last page.)
    3. “VALUE ARROWS up and down to change settings. Don’t you just love hints?

    Kurzweil

    Regarding all Kurzweil Keyboards:

    Sustain Pedal:
    1. You have to plug in the sustain pedal before powering on the keyboard. The OS automatically detects and sets the polarity for the sustain pedal. If you plug it in after you power it up, you may or may not be screwed. Do you feel lucky punk?.. Huh? Well, do ya?
    Resets: Try the softest reset first. Then the Medium reset. If it’s still not working then try the Hard reset last.

    K2000 Series

    Hard Reset Factory Defaults:
    1. Press “Master” Button
    2. Hit “Reset” soft button
    3. “Yes”
    4. “YES” again to confirm.

    K2500 Series (Both Rack mount and Keyboard Units)

    Soft Reset Factory Defaults:
    1. Press all three of the “+/-“, “0" and “Clear” buttons at the same time and release
    2. All lights will flash and the Display will thank you.
    Medium Reset Factory Defaults:
    1. Press the “Master Mode” button
    2. Select “Reset” Soft button
    3. Select “Yes” Soft button
    4. “YES” Again to confirm. After a few seconds it will return to Program Mode page.
    Hard Reset Factory Defaults:
    1. Turn on unit
    2. While booting up it will display “Please wait...” for 2 seconds. Quickly press and release the “Exit” Key
    3. This will load the “Boot Loader”
    4. Arrow to select “Hard Reset”
    5. Press the “OK” Soft button
    6. Press the “UP” and “DOWN” Keys simultaneously
    7. Power off then back on.

    K2600 Series (Both Rack mount and Keyboard Units)

    Soft Reset Factory Defaults:
    1. Press all three of the “+/-“, “0" and “Clear” buttons at the same time and release
    2. All lights will flash and the Display will Welcome you back.
    Medium Reset Factory Defaults:
    1. Hit “Master” button
    2. Press “MAST2" soft button
    3. “Reset” button
    4. Select “Yes”
    5. “Yes” again to confirm.
    Hard Reset Factory Defaults:
    1. Turn on unit
    2. While booting up it will display “Please wait...” for 2 seconds. Quickly press and release the “Exit” Key
    3. This will load the “Boot Loader”
    4. Arrow to select “Hard Reset”
    5. Press the “OK” Soft button
    6. Press the “UP” and “DOWN” Keys simultaneously
    7. Then arrow down to “RUN SYSTEM”
    8. Press “GO”

    PC2

    Soft Reset Factory Defaults:
    1. Press all three of the “+/-“, “0" and “Clear” buttons at the same time and release
    2. All lights will flash and the Display will Welcome you back from the dead.
    Hard Reset Factory Defaults:
    1. System Parameters “Global” Menu button
    2. Hold down the right arrow button under the display until it stops scrolling
    3. Press the LEFT arrow button twice
    4. You should see “Reset PC2?”
    5. “ENTER” (YES)
    6. “ENTER” (YES) again to pass the “Are you sure you really, really , totally wanna to this?”, prompt. Fer sure, totally!

    PC88

    Soft Reset Factory Defaults:
    1. Press all three of the “+/-“, “0" and “Clear” buttons at the same time and release
    2. All lights will flash and the Display will Welcome you back from the dead.
    Hard Reset Factory Defaults:
    1. Hit the “Global” button
    2. Press the RIGHT arrow under the display repeatedly until you see “Reset PC88?”
    3. Hit “Enter” to select
    4. “Enter” again to confirm.

    Nord

    Nord Electro 2 Virtual Electro Mechanical

    Turn Off Write Protect:
    1. Hold “SHIFT” button then press “MEM LOCK” button
    2. UP and DOWN “UNLABELED” buttons to he left of the display to change protect from “ON” (on) and “OF” (off)
    3. “MEM LOCK” to exit.
    Reset Factory Defaults:
    1. Factory programs at: www.clavia.se as a MIDI Sysex file.
    2. Conect the “Midi Out” of the transmitting device to the Electro2's “Midi In”.
    3. You have to then Initiate the transmission on the transmitting device. Oh, bother...
    Sustain Pedal:
    1. Hold “SHIFT” and press “Ped Pol”
    2. UP and DOWN “UNLABELED” buttons to he left of the display to change polarity from “OP” (Open) or “CL” (closed)
    3. “Ped. Pol” button to exit.

    Nord Lead 2Vitural Analog

    Reset Factory Defaults:
    1. Factory program sounds are stored in “A0" to “L9"under the “MANUAL” button that is to the upper left of the Display screen.
    2. This button toggles the Nord between the Factory Presets and the Programable sounds.
    3. Use the Up and DOWN ARROWS to change between sound patches.
    Storing Presets to Programable Locations:
    1. To Store a preset to programable banks
    2. Select the Preset sound you want
    3. Press the RED “STORE” button and the display will flash
    4. Press the “MANUAL” button to toggle to the Programable Banks
    5. Choose the bank you wish to store over
    6. Press the RED “STORE” button again and it will stop flashing.
    Sustain Pedal:
    1. Hold Down the “Shift” button and press “System”
    2. Press “System” button until the first two digits in the display are “SP”
    3. Use program “Up/Down” to switch between “0" = Sustain Pedal - open when pressed and “1" = Sustain Pedal - closed when pressed
    4. “Shift” button again to exit.

    Roland

    A-90 Expandable Controller

    Reset Factory Defaults: There are multiple resets. (Just to make it confusing no doubt)
    1. First press “UTILITY” button
    2. Cursor ARROW RIGHT to select “INT”
    3. Use “CURSOR” ARROWS to select the following one by one:
      1. - “TMP” –> “ENTER” 3 times.
      2. - “MAN” –> “ENTER” 2 times.
      3. - “SYS” –> “ENTER” 3 times.
      4. - “I-ALL” –> “ENTER” 3 times.
    Once you have all four resets your done. Thanks for playing. Come again.

    D-50 Linear Synthesizer

    Turn Off Write Protect:
    1. Press “Tune/Function” hit “Tone/Balance” soft key to select
    2. Set “Protect” to “OFF” by moving the Joystick to the left
    3. “Tune/Function” to set
    4. “Exit” to do just that.
    Reset Factory Defaults:
    1. No Procedure found. However Charlie say’s, “Aww, Come on man.” and we found that you can! With a Little Grey Card. The “PN-D5-00" card in fact.
    2. The card has to end in “00". Insert card
    3. Press “Tune/Function” hit “Tone/Balance” soft key to select
    4. Set “Protect” to “OFF” by moving the JOYSTICK to the LEFT
    5. Hit the RED “Data Transfer” button on the right
    6. Press “Crd–>Int” (L-Tone Edit)
    7. Hit “ENTER” which is a RED button on the Right.

    D-70 Super LA Synthesizer

    Turn Off Write Protect:
    1. Turn OFF the internal memory “Protect SW” switch located on the rear panel.
    Reset Factory Defaults:
    1. Insert RAM card Green and white labeled “Roland D-70 Sounds” into RAM Card slot
    2. “User” button
    3. “F5" (#24)
    4. “F1" (I<–>C)
    5. ”F3" (All)
    6. “F1" (Transfer)
    7. “Enter” button on the top right of Keyboard
    8. Wait until it says “Completed”
    9. Hit “Exit” twice
    10. Turn the internal Memory “Protect SW” located on the rear panel back to the ON position.
    Sustain Pedal:
    1. “USER” button
    2. “F5" (#24)
    3. ARROW to select “Hold Pedal”
    4. “VALUE” Knob to adjust setting
    5. “EXIT” button
    6. “EXIT” again.

    Fantom X6 / X7 / X8

    Reset factory Defaults:
    1. “Menu”
    2. ARROW DOWN to select”Utility”
    3. “ENTER”
    4. ”F3" (Factory Reset)
    5. “F8" (EXEC)
    6. It will ask you to power it down. Do so, then turn on again.
    Sustain Pedal:
    1. “MENU” button
    2. ARROW DOWN to select “SYSTEM”
    3. “ENTER” button
    4. Cursor ARROW down to select “Hold Pedal Polarity” settings
    5. “DEC” and “INC” to modify the settings.

    JD-800 Programmable Synthesizer

    Reset Factory Defaults:
    1. Press “DATA TRANSFER”
    2. Arrow Up/Down to “Factory Preset Y/N”
    3. “INC/YES”

    JP-8000 Synthesizer

    Reset Factory Defaults:
    1. While holding down “SHIFT/EXIT” that is Right of the display
    2. Press “INIT/UTIL” that is below that
    3. The “INIT/UTIL” will then light.
    4. “INIT/UTIL” several times to access Initialize Display.
    5. “UP/DOWN” several times to choose “FACTORY PRESET”
    6. Press “Write” which is to the right of the display.

    JV-80 Multi Timbral Synthesizer

    Turn Off Write Protect:
    1. See “Reset Factory Defaults” below or
    2. Press “WRITE/COMPARE” button
    3. ARROW over to “PROTECT”
    4. “ENTER” button
    5. “DEC” button
    6. ENTER” button.
    Reset Factory Defaults:
    1. Needs Black JV-80 Card.
    2. Insert the “DATA” CARD” into the DATA CARD slot then power on the keyboard.
    3. “Write/Compare” Button
    4. Arrow over to “Card”
    5. “Enter”
    6. Arrow over to “Card–>INT” Selection
    7. ”Enter”
    8. “Enter” Again
    9. Prompt says “Write Protect ON”
    10. Hit “DEC”
    11. “Enter”
    12. Press “Enter” Again.
    Sustain Pedal:
    1. “CONTROL” button
    2. ARROW DOWN possibly three times to “PEDAL POLARITY”
    3. ARROW RIGHT to “HOLD”
    4. “DEC” and “INC” to change setting
    5. “EXIT” button.

    JV-90 Expandable Synthesizer

    Reset Factory Defaults:
    1. Turn power OFF
    2. Hold the Number “8" button down while you power the keyboard back on
    3. Follow the messages on the display and press “Enter”
    4. Press “Write” button.

    JV-1000 Music Workstation

    Reset Factory Defaults:
    1. In the “Number/Perform” Keypad set Hold Down “1" and “8" and turn the keyboard ON.
    2. Yes folks, it can be that easy.

    RD-500

    Reset Factory Defaults:
    1. Switch OFF unit
    2. Turn ON Unit WHILE holding down “1" and “8" in the “Setup Memory” buttons
    3. “DEC/YES”

    RD-600

    Reset Factory Defaults:
    1. “Edit” button, indicator light will light
    2. Press left or right arrows to get to “Initialize All”
    3. Press “INC/YES” button
    4. “INC/YES” again.
    NOTE: Contents of the setup memories “Tone Settings” will not be recalled. Sustain Pedal:
    1. “Edit” button, indicator light will light
    2. Press left or right arrows to get to “DAMPER POLARITY”
    3. “DEC/NO” and “INC/YES” to change settings.

    RD-700

    Reset Factory Defaults:
    1. “Edit” Button on the top right
    2. “Cursor” ARROW down to select “9.Utility”
    3. “Cursor” right to display Edit screen
    4. “Cursor” down to “Factory Reset All”
    5. “Cursor” right
    6. “INC/YES”
    7. “INC/YES” again
    8. “EDIT” button to exit.
    Sustain Pedal:
    1. “EDIT” button on the top right
    2. “CURSOR” ARROW to select “0.System”
    3. “CURSOR” ARROW right 3 times to find “PEDAL POLARITY”
    4. “CURSOR” ARROWS to select ”DAMPERS” setting
    5. “DEC” and “INC” to change settings
    6. “EDIT” button to exit.

    RD-700SX

    Reset Factory Defaults:
    1. “Edit” Button on the top Right
    2. “Cursor” Down to select “9.Utility”
    3. Press “ENTER”
    4. “Cursor” Down to select “Factory Reset All”
    5. “ENTER”
    6. Press “ENTER” again
    7. “ENTER” yet again
    8. When Completed, turn off the power, then power on again.
    Sustain Pedal:
    1. “EDIT” button on the top right
    2. “CURSOR” ARROW to select “0.System”
    3. “ENTER” button
    4. “CURSOR” ARROW RIGHT twice
    5. “Cursor ARROWS to select “DAMPER POLARITY”
    6. “DEC or “INC” to change settings
    7. “EDIT” button to exit.

    U-20 RS-PCM Keyboard

    Reset Factory Defaults:
    1. “DATA”
    2. Cursor right select “Utl”
    3. “ENTER”
    4. Left cursor select “Initialize”
    5. “Enter”
    6. Arrow up or down to select the data group you wish to initialize. (I’d select “ALL” myself) –> “ENTER” –> Press VALUE UP arrow –> Press any play mode select button to exit.

    VK-7

    Reset Factory Defaults:
    1. “Edit” indicators will blink
    2. “7" (UTILITY)
    3. Press left or right arrow about 24 times exactly to select “Factory Setup”
    4. Press he “+” button
    5. “Exit”
    Sustain Pedal:
    1. “EDIT” button
    2. The indicator buttons will blink
    3. Press “1" (System Basic)
    4. Press LEFT ARROW 6 times to select “EX2 POLARITY”
    5. Set to Standard
    6. “+” or “-“ to change. Your only options are “Standard” or “Reverse.”

    VK-8

    Reset factory Defaults:
    1. Turn off the power
    2. Power the unit back on while holding all three of the Harmonic buttons down (Pedal, Lower, Upper) until all of the panel indicators flash. It’s like magic!

    XP-60/80 Music Workstation

    Turn Off Write Protect:
    1. See “Reset Factory Defaults” or
    2. “UTILITY” button
    3. “F5" (Protect) button
    4. “VALUE” wheel to select “ON” or “OFF”
    5. Use the ARROWS “UP” or “DOWN” to select 2 different kinds of Protects
    6. “EXIT” button to exit.
    Reset Factory Defaults:
    1. Go into the “UTILITY” Menu
    2. Press “F6" (Menu) to select Menu 3
    3. “F1" (Preset) to select Factory Presets
    4. “F6" (Execute).
    Note: you may have to turn OFF the “Write Protect” just select it to “OFF” with the “VALUE” wheel –> Press “EXIT” or “ENTER” to close that window to return to where you were in the reset menu.

    XV-88 128 Voices Expandable Synthesizer

    Turn Off Write Protect:
    1. Under the “MODE” section of the keyboard press the “UTILITY” button
    2. It displays “UTIL 1"
    3. on the right select “5. Protect”
    4. Use ARROWS right or left to select between “Internal” and “Exclusive”
    5. “VALUE” wheel to change between “ON” and “OFF”.
    Reset Factory Defaults:
    1. Under the “MODE” section of the keyboard press the “UTILITY” button
    2. ARROW DOWN so it displays “UTIL 2" page
    3. Press the button that selects “4. FACTORY RESET”
    4. Press “ENTER” on far bottom right
    If write protect is on it will now allow you to turn it off
    1. “VALUE” Wheel to turn it to “OFF”
    2. “ENTER” button
    3. “ENTER” button again
    4. And one last “ENTER” just for good measure.

    Roland Modules

    JD- 990 Super JD Synthesizer Module

    Turn Off Write Protect:
    1. Located in the “Utility” Menu on the left
    2. “F6" (PROTECT)
    3. “VALUE” knob to “OFF”
    4. “EXIT” button.
    NOTE: You have to have this turned off to write to the module. Reset Factory Defaults:
    1. “Utility”
    2. “F3" (Init) button
    3. “F1" (Init)
    4. “F6" (EXECUTE)
    5. “F2" (Factory)
    6. “F6" (Execute)
    7. Do this for each of the 16 BANKS
    8. The presets can only be saved to one of those 16 memory slots. So the presets should always be fine... I think...
    Additional Notes: Some sounds are stored in the internal memory but some additional sounds are loaded on using “PCM” and “DATA” cards. There is also “RAM” cards for temporary use after the unit s turned on. There are also expansion boards, tho I’m not sure if there’s one in the unit at this time.

    JV-1080 Super JV 64 Voice Synthesizer Module

    Turn Off Write Protect:
    1. Located in the “Utility” Menu
    2. “PROTECT” soft button
    3. ARROW to select
    4. “VALUE” knob to change settings.
    NOTE: You have to have this turned off to write to the Module. Reset Factory Defaults:
    1. “Utility”
    2. Press the Down Arrow to get to “Utility Menu 2"
    3. Press left button under “Factory Preset”
    4. Press Enter.

    JV-2080 64 Voice Synthesizer Module

  • Turn Off Write Protect:
    1. “UTILITY” button
    2. “F5" (PROTECT) button
    3. ARROWS to select protects
    4. “VALUE” knob to change to “ON” or “OFF”
    5. “EXIT” button twice.
    Reset Factory Defaults:
    1. “Utility”
    2. Press “F6" (Menu) two times to select Menu 3
    3. “F1" (Factory)
    4. “F6" (Execute)
    5. NOTE: If Write Protect is ON then it will display a prompt.
    6. Use the “VALUE” knob to turn it to “OFF”
    7. “F6" (OK)
    8. “F6" (Execute)

    S-750 Digital Sampler

    Reset Factory Defaults:
    1. Must have the “System Disk” to setup as well as the 4 floppy disks that have the sounds
    2. Insert the system disk and hit the power button to install the system
    3. “SYSTEM” button
    4. “Jump”
    5. “F5" (LOAD) button
    6. “F1" (LOAD) button
    7. Repeat for loading Sound Disks etc...

    U-220 RS-PCM Sound Module

    Reset Factory Defaults:
    1. OK, no promises here the manual might as well be written in binary. Here goes...
    2. 0010011101011001...
    3. Which might translate to:
    4. Press “Data” button
    5. Use CURSOR ARROWS to select “Init” (Blinking) press “ENTER”
    6. CURSOR ARROWS to select “ALL” (Blinking) press “Enter”
    7. Press “ENTER” again
    8. “VALUE” UP ARROW
    9. “EXIT” button a total of three times
    10. Your on your own. Don’t say I didn’t warn you. Good Luck!

    XV-5080 128 Voices 8x Expansion / Sample Playback

    Turn Off Write Protect:
    1. Press “System/Utility” Indicator should be blinking, if not hit it again
    2. “F6" (MENU) to select Menu 1
    3. “F5" (PROTECT) button
    4. Turn OFF both Protects
    5. Use ARROWS to select the Protect
    6. “VALUE” knob to change the settings
    7. “EXIT” to do so.
    Reset Factory Defaults:
    1. Press “System/Utility” Indicator should be blinking, if not hit it again.
    2. “F6" (Menu) to select Menu 3
    3. “F1" (Factory)
    4. “F6" (Execute)
    5. If “Write Protect” is on it will prompt you.
    6. Press “DEC” to set “Write Protect” to “Off”
    7. “F6" (OK)
    8. “F6" (Factory) again to execute the Factory Reset.
    9. Take that Write Protect! How do you like be now eh?!

    Yamaha

    CS6X Control Synthesizer / CS6R Tone Generator

    Reset Factory Defaults:
    1. Press “JOB” button in Utility “MODE” which if left of the display
    2. Press “UTILITY” (1) which lights up
    3. Press “JOB"
    4. “ENTER” (3) which is right of the display
    5. “INC/YES” to confirm
    6. “VOICE”

    DX-7II-FD/D

    Turn Off Write Protect:
    1. “Edit” on the left
    2. Press “UTILITY/TUNE” button
    3. You’ll see “MASTER TUNING”
    4. CURSOR ARROWS LEFT or RIGHT to select “INT”
    5. “-1/OFF” to turn off.
    Reset Factory Defaults:
    1. “Edit”
    2. “14" button under “Utility” (TUNE) press 3 times to “Initialize” Screen
    3. With “Voice A” Selected press “+1/ON” (YES) and again to confirm
    4. Using Cursor “>” Select “Voice B” press “+1/ON” (YES) and again to confirm
    5. Using Cursor “>” Select “Performance” press “+1/ON” (YES) and again to confirm
    6. Press “DUAL” button in “VOICE MODE SELECT”
    Sustain Pedal:
    1. “Edit”
    2. Button “27" display says “Sustain Foot Switch” Use cursor <][> to select “A” Press “+1/ON” to turn on
    3. cursor <][> to select “B” Press “+1/ON” to turn on.
    4. This turns on the sustain pedal for both banks.
    5. If you only want it for one Bank then turn off the controller on that bank with the same procedure except hit “-1/OFF” button to turn which ever bank off.

    Motif 6 / Motif 7 / Motif 8 Music Production Synthesizer

    Reset Factory Defaults:
    1. In the Utility “MODE” press “UTILITY” button
    2. Press “JOB” button
    3. “ENTER”
    4. “INC?YES” to confirm
    5. Press “VOICE” to exit.

    Motif-Rack ES Tone Generator

    Reset Factory Defaults:
    1. “UTILITY”
    2. Use “PAGE <][>” buttons to select “JobSel”
    3. Up or down arrows to select “Factory Set”
    4. “MUTE/SEL/ENTER” button to select
    5. “MUTE/SEL/ENTER” again to execute
    6. “EXIT” once completed.
    Sustain Pedal:
    1. “SHIFT” plus “PERFORM”
    2. “EDIT” once or twice
    3. Cursor <][> to select “RcvSw”
    4. “Sustain (Sus)” Turn to on.

    P-200 Electronic Piano

    Turn Off Write Protect:
      The Factory Reset also resets the Protect to N/A
    Reset Factory Defaults:
    1. Turn Off unit then power back on while holding both the “MIDI” and “EDIT” buttons at the same time.
    2. You can also initialize the A or B Bank or voice settings.
    3. Power on the unit while holding down both the “MIDI” button and the “PERF. A”, PERF. B” or “VOICE” button. Whichever applies to want to override.

    P-250 Electronic Piano

    Reset Factory Defaults:
    1. Power the unit on while holding down the right-most white key “C7".
    2. Holding down both the Right-most white key “C7" as well as the right-most Black key “Bb6" it will erase the files in memory as well.
    OR
    1. Press “OTHER SETTING” button repeatedly to “FACTORY SET”
    2. “YES”
    3. “YES” again to confirm
    4. “EXIT” to return from whence ye came.

    S80/90 Music Synthesizer

    Reset Factory Defaults:
    1. In the Utility “MODE” press “UTILITY” button
    2. Press “JOB” button
    3. “ENTER”
    4. “INC/YES” to confirm
    5. Press “VOICE” to exit.

    SY77 / SY99 Music Synthesizer

    Reset Factory Defaults:
    1. Find Disk
    2. “VOICE” + “BANK D” + “8" (The 8 under BANK D)
    3. “COPY”
    4. Your done.
    Sustain Pedal:
    1. “Utility”
    2. Cursor arrow to select “03: Controllers”
    3. “ENTER”
    4. Here you can assign the channels for the Foot, Wheel, and Hold controllers.